Tamping

One of the reasons we decided to write about this topic to launch the blog is the variety of pressing or tamping techniques we have observed in different coffee shops, or among different staff members at the same establishment. Also, the different understandings of this action when asked about it. It is one of the most iconic operations in the barista world, and there are many reasons why proper tamping is crucial.

Why tamp?

Once the coffee has been ground and distributed inside the portafilter, any air pockets that may have become trapped between the coffee particles must be removed to prevent water from flowing through some areas more easily than others, which would result in uneven extraction. This prepares the coffee so that the release and flow of water are uniform throughout the product. Only then will you achieve consistent extraction from espresso to espresso, and minimize the channeling effect to produce sweeter drinks.

With experience and tactile memory, we will also eventually know whether the grind setting we have achieved is correct and whether the distribution and spreading of the coffee in the portafilter is uniform.

Proper tamping.

Knowing that the goal of tamping our coffee is to achieve uniform extraction, it is easy to understand that the best tamping is that which is completely level. Tapping the tamper against the sides should be avoided, as cracks can open around the perimeter that are difficult to seal with a second tamp.

A good technique that personally works for me is to place my index finger and thumb on the edges of the tamper while pushing it down with the rest of my palm. This way, I can ensure that both fingers enter at the same time and the tamper remains level. Another useful tip is to keep your elbow at a 90-degree angle to avoid injury and apply as vertical a force as possible.

When removing the tamper from the portafilter, it is important not to hit the sides and to do so gently so that, in case there is little clearance between the tamper and portafilter, suction cracks do not form. Twisting the tamper at the end is an unnecessary flourish that can be avoided.

How much force should we apply?

We enter the realm of myths and legends. The first is that 20 kilos of force must be applied to the coffee (no more, no less). The second is that very strong pressure reduces the water flow during extraction.

If you think carefully about these claims, of which I personally fell victim for a while, you can deduce that they do not make much sense. Once the coffee has lost the air pockets inside it, trying to compress it further is a waste of time. A light force that does not end up hurting us after hundreds of repetitions and that allows us to better control the level of the coffee is the best option. It is impossible to establish how many kilos it is; it depends on the dose and the grind. What you can notice, however, is the point at which the coffee loses its fluffiness and offers resistance. That is the time to stop. As soon as the coffee comes into contact with water, this compression will be lost, and it will make little difference whether the tamping was 10 or 20 kilos when the pump starts doing its job.

The idea that pressing very hard can reduce the water flow is due to the illusory effect of having left a little more space between the coffee and the shower screen. This gap takes a few moments longer to fill with water, which can confuse the barista and make them think that strong pressure delays the extraction. After this slight delay in the appearance of liquid espresso from the portafilter, the flow will vary little compared to a gentler compression.

Tampers.

We can find two types of tampers: those with a flat base and those that are slightly curved. The latter are designed to push the coffee toward the sides and better seal the space between the coffee and the portafilter, although it has not been proven that they reduce the channeling effect (or chanelling) and they can create an uneven mass with worse extractions. On the contrary, a tamper with a flat base can help us check that the tamping has been completely level and leaves a more homogeneous puck.

What is really important is their diameter and how much clearance they leave relative to the perimeter of the portafilter. Ideally, there should be no more than 0.25 mm between the diameters, but here the portafilter is the problem, since it is not made with as much care and the variation in sizes can be quite large. For this reason, it is recommended to work with VST precision portafilters or similar, whose tolerance is +/- 0.05 mm. The tampers most recommended for working with these portafilters are the Pullman, the Pergtamp by Matt Perger, or the one made by VST.

At the 2015 World Championships, we saw British barista Maxwell Colonna-Dashwood tamp his coffee with a strange contraption that looked like a hockey puck, the famous PUSH. Although we have not yet been able to try it because it is not yet commercially available, in theory, the invention shows promise. The Push is a flat T-shaped disc whose depth can be adjusted for a given dose. In this way, all coffees would have the same pressure, since the top of the tamper stops against the portafilter. A completely flat grind would also be achieved in every operation, making it ideal for coffee shops with many employees or for novice baristas.

Ultimately, tamping is much more than a simple icon of the barista world. Doing it unevenly, tapping the portafilter, or leaving very wide gaps would have almost the same effect as not tamping at all. Therefore, to maintain consistency and get delicious espresso after espresso, you must be aware of how you are applying that pressure and check the level from time to time.

 

 

Pablo Caballero Agudo

Categories
Principal
Tags
TDS barista café café de especialidad cafés especiales espresso extracción ratio refractómetro specialty coffee
//hola.coffee/cdn/shop/t/26/assets/logo-peque.png?v=58915777662213944981784019439